A liquid jet can stably bounce off a sufficiently soft gel by following the contour of the dimple created upon impact. This new phenomenon is insensitive to the wetting properties of the gels and was observed for different liquids over a wide range of surface tensions, γ = 24 − 72 mN/m. In contrast, other jet rebound phenomena are typically sensitive to γ: only a high γ jet rebounds off a hard solid (e.g. superhydrophobic surface) and only a low γ jet bounces off a liquid bath. This is because an air layer must be stabilized between the two interfaces. For a soft gel, no air layer is necessary and the jet rebound remains stable even when there is direct liquid-gel contact.

Recently, there has been much interest in using lubricated surfaces to achieve extreme liquid repellency: a foreign droplet immiscible with the underlying lubricant layer was shown to slide o at a small tilt angle <5◦ . This behaviour was hypothesized to arise from a thin lubricant overlayer film sandwiched between the droplet and solid substrate, but this has not been observed experimentally. Here, using thin-film interference, we are able to visualize the intercalated film under both static and dynamic conditions. We further demonstrate that for a moving droplet, the film thickness follows the Landau–Levich–Derjaguin law. The droplet is therefore oleoplaning—akin to tyres hydroplaning on a wet road—with minimal dissipative force and no contact line pinning. The techniques and insights presented in this study will inform future work on the fundamentals of wetting for lubricated surfaces and enable their rational design.

We provide an overview of our recent advances in the manipulation of wetting in inverse-opal photonic crystals. Exploiting photonic crystals with spatially patterned surface chemistry to confine the infiltration of fluids to liquidspecific spatial patterns, we developed a highly selective scheme for colorimetry, where organic liquids are distinguished based on wetting. The high selectivity of wetting, upon-which the sensitivity of the response relies, and the bright iridescent color, which disappears when the pores are filled with liquid, are both a result of the highly symmetric pore structure of our inverse-opal films. The application of horizontally or vertically orientated gradients in the surface chemistry allows a unique response to be tailored to specific liquids. While the generic nature of wetting makes our approach to colorimetry suitable for applications in liquid authentication or identification across a broad range of industries, it also ensures chemical non-specificity. However, we show that chemical specificity can be achieved combinatorially using an array of indicators that each exploits different chemical gradients to cover the same dynamic range of response. Finally, incorporating a photo-responsive polyelectrolyte surface layer into the pores, we are able to dynamically and continuously photo-tune the wetting response, even while the film is immersed in liquid. This in situ optical control of liquid percolation in our photonic-crystal films may also provide an error-free means to tailor indicator response, naturally compensating for batch-to-batch variability in the pore geometry.

Various life forms in nature display a high level of adaptability to their environments through the use of sophisticated material interfaces. This is exemplifi ed by numerous biological systems, such as the self-cleaning of lotus leaves, the water-walking abilities of water striders and spiders, the ultra-slipperiness of pitcher plants, the directional liquid adhesion of butterfl y wings, and the water collection capabilities of beetles, spider webs, and cacti. The versatile interactions of these natural surfaces with fl uids, or special wettability, are enabled by their unique micro/nanoscale surface structures and intrinsic material properties. Many of these biological designs and principles have inspired new classes of functional interfacial materials, which have remarkable potential to solve some of the engineering challenges for industrial and biomedical applications. In this article, we provide a snapshot of the state of the art of biologically inspired materials with special wettability, and discuss some promising future directions for the field.

When a fluid-immersed array of supported plates or pillars is dried, evaporation leads to the formation of menisci on the tips of the plates or pillars that bring them together to form complex patterns. Building on prior experimental observations, we use a combination of theory and computation to understand the nature of this instability and its evolution in both the two- and three-dimensional setting of the problem. For the case of plates, we explicitly derive the interaction torques based on the relevant physical parameters associated with pillar deformation, contact-line pinning/depinning and fluid volume changes. A Bloch-wave analysis for our periodic mechanical system captures the window of volumes where the two-plate eigenvalue characterizes the onset of the coalescence instability. We then study the evolution of these binary clusters and their eventual elastic arrest using numerical simulations that account for evaporative dynamics coupled to capillary coalescence. This explains both the formation of hierarchical clusters and the sensitive dependence of the final structures on initial perturbations, as seen in our experiments. We then generalize our analysis to treat the problem of pillar collapse in three dimensions, where the fluid domain is completely connected and the interface is a minimal surface with the uniform mean curvature. Our theory and simulations capture the salient features of experimental observations in a range of different situations and may thus be useful in controlling the ensuing patterns.

Controlling the microscopic wetting state of a liquid in contact with a structured surface is the basis for the design of liquid repellent as well as anti-fogging coatings by preventing or enabling a given liquid to infiltrate the surface structures. Similarly, a liquid can be confined to designated surface areas by locally controlling the wetting state, with applications ranging from liquid transport on a surface to creating tailored microenvironments for cell culture or chemical synthesis. The control of the wetting of a low-surfacetension liquid is substantially more difficult compared to water and requires surface structures with overhanging features, known as re-entrant geometries. Here, we use colloidal self-assembly and templating to create two-dimensional nanopore arrays with tailored re-entrant geometry. These pore arrays, termed inverse monolayers, are prepared by backfilling a sacrificial colloidal monolayer with a silica sol–gel precursor material. Varying the precursor concentration enables us to control the degree to which the colloids are embedded into the silica matrix. Upon calcination, nanopores with different opening angles result. The pore opening angle directly correlates with the re-entrant curvature of the surface nanostructures and can be used to control the macroscopic wetting behavior of a liquid sitting on the surface structures. We characterize the wetting of various liquids by static and dynamic contact angles and find correlation between the experimental results and theoretical predictions of the wetting state based on simple geometric considerations. We demonstrate the creation of omniphobic surface coatings that support Cassie–Baxter wetting states for liquids with low surface tensions, including octane (g ¼ 21.7 mN m1). We further use photolithography to spatially confine such low-surface-tension liquids to desired areas of the substrate with high accuracy.

Omniphobic fluorogel elastomers were prepared by photocuring perfluorinated acrylates and a perfluoropolyether crosslinker. By tuning either the chemical composition or the temperature that control the crystallinity of the resulting polymer chains, a broad range of optical and mechanical properties of the fluorogel can be achieved. After infusing with fluorinated lubricants, the fluorogels showed excellent resist- ance to wetting by various liquids and anti-biofouling behavior, while maintaining cytocompatiblity.