Ice repellent coatings have been studied and keenly sought after for many years, where any advances in the durability of such coatings will result in huge energy savings across many fields. Progress in creating anti-ice and anti-frost surfaces has been particularly rapid since the discovery and development of slippery, liquid infused porous surfaces (SLIPS). Here we use SLIPS-coated differential scanning calorimeter (DSC) pans to investigate the effects of the surface modification on the nucleation of supercooled water. This investigation is inherently different from previous studies which looked at the adhesion of ice to SLIPS surfaces, or the formation of ice under high humidity conditions. Given the stochastic nature of nucleation of ice from supercooled water, multiple runs on the same sample are needed to determine if a given surface coating has a real and statistically significant effect on the nucleation temperature. We have cycled supercooling to freezing and then thawing of deionized water in hydrophilic (untreated aluminum), hydrophobic, superhydrophobic, and SLIPS-treated DSC pans multiple times to determine the effects of surface treatment on the nucleation and subsequent growth of ice. We find that SLIPS coatings lower the nucleation temperature of supercooled water in contact with statistical significance and show no deterioration or change in the coating performance even after 150 freeze–thaw cycles.
Omniphobic surfaces that can repel fluids at temperatures higher than 100 °C are rare. Most state-of-the-art liquid-repellent materials are based on the lotus effect, where a thin air layer is maintained throughout micro/nanotextures leading to high mobility of liquids. However, such behavior eventually fails at elevated temperatures when the surface tension of test liquids decreases significantly. Here, we demonstrate a class of lubricant-infused structuredsurfaces that can maintain a robust omniphobic state even for low-surface-tension liquids at temperatures up to at least 200 °C. We also demonstrate how liquid mobility on such surfaces can be tuned by a factor of 1000.
Rational design strategies for mechano‐responsive optical material systems are created by introducing a simple experimental system that can continuously vary the state of bi‐axial stress to induce various wrinkling patterns, including stripes, labyrinths, herringbones, and rarely observed checkerboards, that can dynamically tune the optical properties. In particular, a switching of two orthogonally oriented stripe wrinkle patterns from oxidized polydimethylsiloxane around the critical strain value is reported, as well as the coexistence of these wrinkles forming elusive checkerboard patterns, which are predicted only in previous simulations. These strain‐induced wrinkle patterns give rise to dynamic changes in optical transmittance and diffraction patterns. A theoretical description of the observed pattern formation is presented which accounts for the residual stress in the membrane and allows for the fine‐tuning of the window of switching of the orthogonal wrinkles. Applications of wrinkle‐induced changes in optical properties are demonstrated, including a mechanically responsive instantaneous privacy screen and a transparent sheet that reversibly reveals a message or graphic and dynamically switches the transmittance when stretched and released.
The emergence of complex nano- and microstructures is of fundamental interest, and the ability to program their form has practical ramifications in fields such as optics, catalysis, and electronics. We developed carbonate-silica microstructures in a dynamic reaction-diffusion system that allow us to rationally devise schemes for precisely sculpting a great variety of elementary shapes by diffusion of carbon dioxide (CO2) in a solution of barium chloride and sodium metasilicate. We identify two distinct growth modes and show how continuous and discrete modulations in CO2 concentration, pH, and temperature can be used to deterministically switch between different regimes and create a bouquet of hierarchically assembled multiscale microstructures with unprecedented levels of complexity and precision. These results outline a nanotechnology strategy for "collaborating" with self-assembly processes in real time to build arbitrary tectonic architectures.
Certain natural organisms use micro‐patterned surface chemistry, or ice‐nucleating species, to control water condensation and ice nucleation for survival under extreme conditions. As an analogy to these biological approaches, it is shown that functionalized, hydrophilic polymers and particles deposited on the tips of superhydrophobic posts induce precise topographical control over water condensation and freezing at the micrometer scale. A bottom‐up deposition process is used to take advantage of the limited contact area of a non‐wetting aqueous solution on a superhydrophobic surface. Hydrophilic polymer deposition on the tips of these geometrical structures allows spatial control over the nucleation, growth, and coalescence of micrometer‐scale water droplets. The hydrophilic tips nucleate water droplets with extremely uniform nucleation and growth rates, uniform sizes, an increased stability against coalescence, and asymmetric droplet morphologies. Control of freezing behavior is also demonstrated via deposition of ice‐nucleating AgI nanoparticles on the tips of these structures. This combination of the hydrophilic polymer and AgI particles on the tips was used to achieve templating of ice nucleation at the micrometer scale. Preliminary results indicate that control over ice crystal size, spatial symmetry, and position might be possible with this method. This type of approach can serve as a platform for systematically analyzing micrometer‐scale condensation and freezing phenomena, and as a model for natural systems.
Colourimetric sensors and indicators are widely used because of their low cost and simplicity. A significant challenge associated with the design of this type of device is that the sensing mechanism must be simultaneously optimised for the sensitivity of the response and a visually perceptible colour change. Structural colour, derived from coherent scattering rather than molecular absorption, is a promising route to colourimetric sensor design because colour shifts are tied to changes in one of many physical properties of a material, rather than a specific chemical process. This Feature Article presents an overview of the development of low-cost sensors and indicators that exploit structural colour. Building upon recent advances in structurally adaptive materials design, structural colour sensors have been developed for a wide variety of previously inaccessible physical (e.g. temperature, strain, electric fields) and chemical stimuli (e.g. small organic molecules, charged species, biomacromolecules and metabolites). These devices, often exceeding the state of the art in performance, simplicity or both, have bright prospects for market impact in areas such as environmental monitoring, workplace hazard identification, threat detection, and point-of-care diagnostics. Finding the ideal balance between performance (e.g. sensitivity, specificity, reproducibility, etc.) and simplicity (e.g. colourimetric vs. spectroscopic readout) will be one of the most critical elements in the further development of structural colour sensors. This balance should be driven largely by the market demands and competing technologies.
A transparent coating that repels a wide variety of liquids, prevents staining, is capable of self-repair and is robust towards mechanical damage can have a broad technological impact, from solar cell coatings to self-cleaning optical devices. Here we employ colloidal templating to design transparent, nanoporous surface structures. A lubricant can be firmly locked into the structures and, owing to its fluidic nature, forms a defect-free, self-healing interface that eliminates the pinning of a second liquid applied to its surface, leading to efficient liquid repellency, prevention of adsorption of liquid-borne contaminants, and reduction of ice adhesion strength. We further show how this method can be applied to locally pattern the repellent character of the substrate, thus opening opportunities to spatially confine any simple or complex fluids. The coating is highly defect-tolerant due to its interconnected, honeycomb wall structure, and repellency prevails after the application of strong shear forces and mechanical damage. The regularity of the coating allows us to understand and predict the stability or failure of repellency as a function of lubricant layer thickness and defect distribution based on a simple geometric model.